Failure Analysis and Thermo-Structural Design Simulation of a Cylindrical Dual-Chamber Solid Waste Incinerator
Main Article Content
Abstract
The generation of municipal solid waste (MSW) is rapidly increasing. This has worsened environmental pollution and public health hazards, especially in places with poor waste management policies. This research employs finite element simulation techniques to investigate the thermo-structural response and failure behaviour of a cylindrical dual-chamber MSW incinerator. The study's objectives were to assess the structural stability and operational reliability of the system under various service situations. A three-dimensional computer-aided model of the incinerator was developed using CATIA CAD modelling. Finite Element simulations were used to analysed various operational fault conditions like over-heating, refractory deterioration, chamber deformation, cracking, corrosion, chimney blockage, seal leakage and ash accumulation. The main structural material was mild steel, with refractory linings used mainly to improve insulation and also to prevent the combustion chambers from high temperatures. The numerical analysis was performed with tetrahedral meshing and appropriate thermal boundary conditions. The simulation results showed that the combustion chambers and connecting duct had the highest temperature distribution, and the major thermal stresses were concentrated around the welded joints and support regions. During normal operation, the secondary chamber temperatures ranged from 995°C to 1050°C, and the maximum Von Mises stress ranged from 145 MPa to 180 MPa. The results indicated that repetitive thermal cycling, corrosion, inadequate airflow circulation and excessive heat loading increased the likelihood of deformation and structural collapse. The study showed that the cylindrical dual-chamber design had better heat distribution, lower stress concentration and better combustion performance when compared to the conventional rectangular incinerator.
Article Details
Copyright (c) 2026 Wisdom Noweghoweman, Dr. Ejiroghene Kelly Orhorhoro, Andrew Ngbeneme (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
Bahareh, H., Ashkan, Nabavi-Pelesaraei (2025). Systematic review on environmental impact assessment of incineration technologies. Energy Conversion and Management, 26, 101039. https://doi.org/10.1016/j.ecmx.2025.101039 DOI: https://doi.org/10.1016/j.ecmx.2025.101039
Budinski, K. G., & Budinski, M. K. (2010). Engineering materials: Properties and selection (9th ed.). Pearson.
Cao, H., Jin, Y., Song, X., Wang, Z., Liu, B., & Wu, Y. (2023). Computational Fluid Dynamics Simulation of Combustion and Selective Non-Catalytic Reduction in a 750 t/d Waste Incinerator. Processes, 11(9), 2790. https://doi.org/10.3390/pr11092790 DOI: https://doi.org/10.3390/pr11092790
Callister, W. D., & Rethwisch, D. G. (2020). Materials science and engineering: An introduction (10th ed.). John Wiley & Sons.
Doppalapudi, A. T., Azad, A. K., & Khan, M. M. K. (2023). Analysis of Improved In-Cylinder Combustion Characteristics with Chamber Modifications of the Diesel Engine. Energies, 16(6), 2586. https://doi.org/10.3390/en16062586 DOI: https://doi.org/10.3390/en16062586
Erhinyodavwe, O., Orhorhoro, E. K., & Amize, H. (2025). Categorization of plastic waste generated for conceptualization of pyrolysis plant development in Agbor Town, Delta State, Nigeria. Journal of Applied Sciences and Environmental Management, 29(6), 1890–1897. https://doi.org/10.4314/jasem.v29i6.20 DOI: https://doi.org/10.4314/jasem.v29i6.20
Green, D. W., & Southard, M. Z. (Eds.). (2019). Perry's chemical engineers' handbook (9th ed.). McGraw-Hill Education.
Hadadiyan, M., Arjmandi, H., Abderrahmane Deme, O., Eghbali, M.J. (2023). Integrated optimization of geometrical parameters and flow variables for industrial incinerator performance improvement. Results Eng., 20, 101577 DOI: https://doi.org/10.1016/j.rineng.2023.101577
Huai, X., Xu, W., Qu, Z., Li, Z., Zhang, F., Xiang, G., Zhu, S., Chen, G. (2008). Numerical simulation of municipal solid waste combustion in a novel two-stage reciprocating incinerator. Waste Manag., 28, 15–29 DOI: https://doi.org/10.1016/j.wasman.2006.11.010
Jiang, M., Lai, A.C.H., Law, A.W.K. (2020). Solid waste incineration modelling for advanced moving grate incinerators. Sustainability, 12, 8007 DOI: https://doi.org/10.3390/su12198007
Jin, G., Wang, M., Chen, L., Zhang, J., He, W., Guo, Q. (2023). Numerical simulation of the effect of the near-ground explosion of energetic materials on the shell of a vertical incinerator. J. Phys. Conf. Ser., 2478, 072018. DOI: https://doi.org/10.1088/1742-6596/2478/7/072018
Jun, Y., Zhaoxi, L., Jun, W. (2026). Valorization of municipal solid waste incineration bottom ash in ecological cement mortar: Mechanical enhancement, effective immobilization of hazardous heavy metals, and life cycle environmental benefits. Case Studies in Construction Materials, 24. https://doi.org/10.1016/j.cscm.2025.e05718 DOI: https://doi.org/10.1016/j.cscm.2025.e05718
Kim, R.M., Johan, B.P., Helge, B. (2024). Incineration economy: Waste management policy failing the circular economy transition in Norway, Resources, Conservation and Recycling, 210,107838. https://doi.org/10.1016/j.resconrec.2024.107838 DOI: https://doi.org/10.1016/j.resconrec.2024.107838
Liu, X., Zhu, G., Asim, T., Mishra, R. (2024). Design of a novel α-shaped flue gas route flame incinerator for the treatment of municipal waste materials. Waste Biomass Valorization, 15, 1179–1193. DOI: https://doi.org/10.2139/ssrn.4378204
Luo, Z., Chen, W., Wang, Y., Cheng, Q., Yuan, X., Li, Z., Yang, J. (2021). Numerical simulation of combustion and characteristics of fly ash and slag in a “V-type” waste incinerator. Energies, 14, 7518 DOI: https://doi.org/10.3390/en14227518
Mou, Y., Han, S., Zhang, Y., Wu, K., & Shen, X. (2025). Numerical Analysis of Incinerator Refractory Brick with Coupled Parameters Based on Thermodynamic Theory. Materials, 18(4), 824. https://doi.org/10.3390/ma18040824 DOI: https://doi.org/10.3390/ma18040824
Omari, A.M., John P. J., Baraka, K. (2020). Simulation and Optimization of Municipal Solid Waste Combustion: A Case Study of a Fixed Bed Incinerator. Journal of Engineering Research and Reports 11 (3), 5-19. https://doi.org/10.9734/jerr/2020/v11i317060 DOI: https://doi.org/10.9734/jerr/2020/v11i317060
Orhorhoro, E. K. (2025). A review of plastic waste management for a sustainable environment: Composition and approaches. European Journal of Sustainable Development Research, 9(3), Article em0314. https://doi.org/10.29333/ejosdr/16359 DOI: https://doi.org/10.29333/ejosdr/16359
Peng, Y., Xin, T., Yitong, Z., Shuyang, L., Yangfan, P., Sheng, H. (2025). Sustainable municipal solid waste incineration fly ash–based Engineered Geopolymer Composites (EGC) with high ductility. Construction and Building Materials, 476,141230. https://doi.org/10.1016/j.conbuildmat.2025.141230 DOI: https://doi.org/10.1016/j.conbuildmat.2025.141230
Ventura, S., & Maia, L. (2025). Municipal solid waste incineration slag as potential materials in green engineering as partial or total substitutes for conventional cement in future decades. Discov Appl Sci 7, 339. https://doi.org/10.1007/s42452-025-06574-5 DOI: https://doi.org/10.1007/s42452-025-06574-5
Wosu, C.O., Shaba, H.I., Ojong, O.E. (2025). Design and Simulation of Incineration Plant for Municipal Solid Wastes Management in Kano Metropolis. International Journal of Chemistry and Chemical Processes, 11(4), 32-62. https://10.56201/ijccp.vol.11.no4.2025.pg32.62
Xiaoxin, Z., Jin, H., Ling, L., Sinan, Z. (2020). Current status of technology and standards of domestic solid waste incineration in China. IOP Conf. Ser. Earth Environ. Sci., 510, 042035 DOI: https://doi.org/10.1088/1755-1315/510/4/042035
Yang, Z., Zhi, J.B., Lin, F.Z., Xiang, G. (2023). Study on Finite Element Method for Solving Stress Concentration Problem. Applied Mechanics and Materials, 914, 175-180. https://doi:10.4028/p-o061r2 DOI: https://doi.org/10.4028/p-o061r2
Zhang, L., Yang, F., Xu, L., Zhang, S., & Ren, X. (2025). Numerical Simulation and Structural Optimization of Combustion Processes in a 750 t/d Waste Incinerator. Energies, 18(2), 384. https://doi.org/10.3390/en18020384 DOI: https://doi.org/10.3390/en18020384
Zheng, M., Sun, J., Gong, L., Fan, Y., Tu, J., Dong, J. (2024). Optimization of secondary air operation parameters of waste incineration boiler based on response surface methodology. Appl. Therm. Eng., 236, 121763. DOI: https://doi.org/10.1016/j.applthermaleng.2023.121763